Whole Home Pipe Replacement (Repipe) in Odessa and West Texas
Replace failing galvanized, polybutylene, or copper pipes throughout your entire home with modern PEX or copper from a licensed team that has repiped hundreds of Permian Basin homes.
Fast Answer
Whole Home Pipe Replacement Cost in Odessa TX
| Service | Typical Cost Range |
|---|---|
| PEX repipe (1-bath home, <1,200 sq ft) | $3,800 - $5,500 |
| PEX repipe (2-bath home, 1,200-1,800 sq ft) | $5,500 - $8,000 |
| PEX repipe (3+ bath home, 1,800-2,500 sq ft) | $8,000 - $12,000 |
| Copper repipe (add 30-50% over PEX) | $6,000 - $18,000 |
| Drywall patching (included in most quotes) | Included |
| Water softener bundle discount | 10% off softener install |
Prices reflect our 2025-2026 project records for the Odessa-Midland area. Call (432) 290-8511 for a free estimate.
Why Permian Basin Homes Need Repiping
Odessa and Midland sit on some of the hardest water in Texas. Municipal water here regularly tests above 20 grains per gallon, and private wells can exceed 30. That mineral load corrodes galvanized steel from the inside out, narrowing the pipe bore until water pressure drops to a trickle.
Polybutylene (the gray or blue plastic pipe installed in many homes from the late 1970s through the mid-1990s) becomes brittle in hard water and cracks without warning. According to the U.S. Census Bureau, roughly 40 percent of housing units in Ector County were built before 1980, which means tens of thousands of homes may still have original galvanized supply lines.
Our team recently repiped a 1,600-square-foot home on Dixie Boulevard in Odessa that had galvanized pipes so choked with mineral scale that the kitchen faucet produced barely a pencil-width stream. After a full Uponor PEX-A repipe, the homeowner said the water pressure felt like a different house.
PEX vs. Copper: Which Material Is Right?
Both Uponor PEX-A and Type L copper are approved under the Texas State Board of Plumbing Examiners (TSBPE) code for residential supply lines. PEX tubing offers several advantages in the Permian Basin. It resists scale buildup better than copper, flexes to absorb the expansion that comes with West Texas temperature swings from 110-degree summers to occasional hard freezes, and installs with fewer fittings, which reduces potential leak points.
Copper remains an excellent material and some homeowners prefer its proven track record. We use SharkBite or Uponor ProPEX fittings for PEX installations and lead-free solder joints for copper work. Both materials carry manufacturer warranties of 25 years or more.
We walk every homeowner through the pros and cons so you can make a confident choice.
What to Expect During Your Repipe
A full repipe is a multi-day project, but it does not have to be chaotic. Day one, we map the pipe layout, cut small access openings in drywall, and begin running new supply lines from the main shutoff to each fixture. We work room by room and keep water running to at least one bathroom at all times.
On subsequent days, we connect remaining fixtures, install new angle stops (the small shutoff valves behind toilets and under sinks), and pressure-test the entire system to 80 PSI for a minimum of two hours. Once everything passes, we patch access openings and leave the walls ready for texture and paint. Most homes between 1,000 and 2,000 square feet take 2 to 4 days.
Larger or multi-story homes may take up to 5 days. Call (432) 290-8511 to schedule a free repipe consultation.
Signs Your Home Needs a Repipe
Rusty or brown water when you first turn on a faucet is the most obvious sign. Low water pressure across the entire house, frequent pinhole leaks patched with hose clamps, visible green or white corrosion on exposed pipes, and water stains on ceilings or walls all indicate widespread pipe failure. If you have had two or more leaks in different areas of the house within the past year, a full repipe will cost less than continued spot repairs over time.
According to HomeAdvisor, the average cost of water damage repair in the U.S. is over $3,500, and a single burst galvanized pipe can easily cause that much damage overnight. Repiping eliminates the risk entirely.
Protecting Your Investment After the Repipe
New pipes perform best when the water running through them is treated. We strongly recommend pairing your repipe with a water softener installation to prevent the same scale buildup that destroyed the original pipes. A Fleck or Kinetico water softener sized for your household reduces hardness to safe levels and extends the life of your new PEX or copper pipes by decades.
We also recommend installing a whole-house sediment filter upstream of the softener to catch sand, rust, and particulate common in Permian Basin water supplies. Ask us about bundled pricing when you combine a repipe with a water softener install.
How Whole Home Pipe Replacement Works
In-Home Evaluation
We inspect exposed pipes, test water pressure at multiple fixtures, check pipe material and diameter, and map the layout of your existing plumbing. We provide a written scope of work and fixed-price quote.
Material Selection and Scheduling
You choose between Uponor PEX-A and Type L copper based on budget and preference. We order materials and schedule the project to minimize disruption to your routine.
Demolition and Pipe Routing
We cut small, strategic access openings in drywall and ceilings to route new supply lines. We use RIDGID press tools for copper connections and Uponor ProPEX expansion rings for PEX.
Connection and Pressure Testing
Every fixture receives new supply lines and angle stop valves. We pressure-test the complete system at 80 PSI for a minimum of two hours to verify zero leaks before closing any walls.
Wall Repair and Final Walkthrough
We patch all access openings with drywall and leave them ready for texture and paint. We walk you through the new system, show you the main shutoff, and answer any questions.
PEX vs. Copper Pipe for Repiping
| Factor | PEX (Uponor PEX-A) | Copper (Type L) |
|---|---|---|
| Scale resistance | Excellent (smooth bore) | Good (scale can adhere) |
| Freeze resistance | Expands without cracking | Can burst if frozen solid |
| Installation speed | Faster (fewer joints) | Slower (solder each joint) |
| Material cost | Lower | Higher (30-50% more) |
| Lifespan | 25+ years (warranty) | 50+ years (proven track record) |
| Best for Odessa | Most homeowners | Those who prefer traditional copper |
More Plumbing Services
Resolv Services provides whole home pipe replacement as part of our plumbing across West Texas.
Whole Home Pipe Replacement
Get a written estimate for whole home pipe replacement — no obligation.
(432) 290-8511Common Questions About Whole Home Pipe Replacement
Most Odessa homes between 1,000 and 2,000 square feet take 2 to 4 days. Larger or multi-story homes may take up to 5 days. We keep at least one bathroom functional throughout the project so you can stay in the home.
No. We work room by room and maintain water service to at least one bathroom at all times. There will be some dust and noise from cutting access openings, but most families stay home comfortably during the process.
Yes. Uponor PEX-A is certified to NSF/ANSI 61 for drinking water contact, approved under the Texas Plumbing Code, and used in millions of homes across the country. It does not leach harmful chemicals and carries a 25-year manufacturer warranty.
A full repipe removes one of the biggest red flags for home buyers and inspectors. Homes with new plumbing sell faster and often appraise higher than comparable homes with aging galvanized or polybutylene pipes. It is one of the best return-on-investment plumbing upgrades you can make.
Need Whole Home Pipe Replacement?
Get a written estimate for professional whole home pipe replacement in the Permian Basin.
(432) 290-8511